Search found 59 matches

by Meanoldfireman
Mon Feb 06, 2017 3:34 am
Forum: Racks, Switching Systems and MIDI
Topic: Selectable buffer on GCX?
Replies: 6
Views: 3607

Re: Selectable buffer on GCX?

That's what I was looking for. Thanks John.
by Meanoldfireman
Sat Jan 28, 2017 1:39 pm
Forum: Racks, Switching Systems and MIDI
Topic: Selectable buffer on GCX?
Replies: 6
Views: 3607

Re: Selectable buffer on GCX?

Both of those would work. Related question: the normaling of the jacks, they're switched at the front? That is, the rear jacks are in parallel until something gets plugged it the front "feed though"? I'd like to feed the buffer from the rear...output of loop 1 (fuzz) to the rear feedthrough, jumper ...
by Meanoldfireman
Thu Jan 26, 2017 7:58 pm
Forum: Racks, Switching Systems and MIDI
Topic: Selectable buffer on GCX?
Replies: 6
Views: 3607

Selectable buffer on GCX?

Is there a way to patch the buffer into loop 1 so I can take it out of circuit when I use my fuzz?
by Meanoldfireman
Sat Jan 30, 2016 7:05 pm
Forum: Racks, Switching Systems and MIDI
Topic: Control Switcher with GCX loops ?
Replies: 5
Views: 2957

Re: Control Switcher with GCX loops ?

It sounds like you have an abundance of things to control, you just need a better way to control them. There are a lot of things to consider in upgrading your controller. A small foot print is nice, but the flexibility to get what you need done is very important. (And you don't need to necessarily c...
by Meanoldfireman
Sat Jan 30, 2016 6:42 pm
Forum: Racks, Switching Systems and MIDI
Topic: second Midi pedal for IAs
Replies: 5
Views: 2901

Re: second Midi pedal for IAs

I think you can run the MIDI mate into the GCP and pass the CC messages on to other devices. You didn't say what else you were controlling. If you're controlling a GCX, I'd not sure what will happen if it can get the SYS Ex messages from the GCP and the CC messages from the MIDI mate. What are you c...
by Meanoldfireman
Sat Jan 30, 2016 6:27 pm
Forum: Racks, Switching Systems and MIDI
Topic: GCX not powering the GCP
Replies: 6
Views: 3273

Re: GCX not powering the GCP

Be sure that the cables have all five pins connected. Also (especially if you aquired the GCP used) be sure that the DIN Jack on the GCP is clean. (Power it down and give it a blast of contact cleaner.)
by Meanoldfireman
Sat Jan 30, 2016 6:14 pm
Forum: Racks, Switching Systems and MIDI
Topic: GCX engaging presets on multiple devices (one stomp)
Replies: 5
Views: 2706

Re: GCX engaging presets on multiple devices (one stomp)

If you want to conservce loops in the GCX (and simplify the wiring) you can wire the Strymon between the Output of the GCX and the input of the amp, or directly in the effects loop of the amp and program a preset in the Strymon with all dry signal. When you send the PC message and change to the "dry...
by Meanoldfireman
Fri Jan 29, 2016 3:11 pm
Forum: Racks, Switching Systems and MIDI
Topic: Multiple Amp Switching GCX
Replies: 4
Views: 2998

Re: Multiple Amp Switching GCX

Hello, and welcome!! What you want to do is dead simple, and the best part is you can do it with a single GCX Loop. Check out Example 2 on Page 8 of the GCX Manual. This is the easiest way to make your front end connections, and all you'll need to do is split the signals coming out of Send and Out ...
by Meanoldfireman
Fri Jan 29, 2016 11:04 am
Forum: Racks, Switching Systems and MIDI
Topic: Multiple Amp Switching GCX
Replies: 4
Views: 2998

Re: Multiple Amp Switching GCX

Simple enough. Are you running the amp pairs in stereo or mono?
by Meanoldfireman
Tue Jan 26, 2016 8:50 pm
Forum: Racks, Switching Systems and MIDI
Topic: second Midi pedal for IAs
Replies: 5
Views: 2901

Re: second Midi pedal for IAs

I'll be curious to hear if you can make it work. You won't be able to send the CC messages from the ia's withe the presets. You would probably be better off with a single more sophisticated controller.