Search found 7261 matches

by JohnClark
Wed May 29, 2019 9:38 pm
Forum: Racks, Switching Systems and MIDI
Topic: Installing control switcher
Replies: 1
Views: 379

Re: Installing control switcher

After a factory reset, the Control Switcher should just auto configure itself in this rig. However, here are some things to be sure to try... MIDI Connections I'm not sure what other MIDI gear you may have, but at least for a test be sure to connect as follows: 1. Ground Control Pro MIDI Out to GCX ...
by JohnClark
Tue May 28, 2019 5:07 pm
Forum: Racks, Switching Systems and MIDI
Topic: Setting GCX and GCP stereo with 2 amps and effect pedals
Replies: 6
Views: 731

Re: Setting GCX and GCP stereo with 2 amps and effect pedals

I do not have any specific suggestions for a splitter... sorry! I suppose we can see what we can get away with by using the SDD-300 as a split. For the signal routing it looks like everything will be routed in front of the amps. This is probably easier anyway ;) 1. Connect the Out of the last GCX Lo...
by JohnClark
Tue May 28, 2019 11:10 am
Forum: Pedalboards and Effects
Topic: GCX Switching Problems... Thx for Help
Replies: 1
Views: 370

Re: GCX Switching Problems... Thx for Help

The picture helps a lot! Thanks! 1. On Loop 3 Out you have two lines to feed both Triaxis Returns... what is the cable you are using here? If this is an Insert Point Cable then certainly get rid of it ;) This should only need to be a single mono cable to one of the FX Returns (usually Left for Mono)...
by JohnClark
Tue May 28, 2019 10:51 am
Forum: Racks, Switching Systems and MIDI
Topic: Setting GCX and GCP stereo with 2 amps and effect pedals
Replies: 6
Views: 731

Re: Setting GCX and GCP stereo with 2 amps and effect pedals

If you have pedals that will be in front of the amps that need to be available to either amp (or both amps at once), you will need a splitter of some sort. A buffered split would probably be best, or anything that transformer isolates one amp from the other, but a simple Y Cable (all ends Mono) will...
by JohnClark
Tue May 28, 2019 10:33 am
Forum: Racks, Switching Systems and MIDI
Topic: HELP - GCX overheated and cut out?
Replies: 4
Views: 607

Re: HELP - GCX overheated and cut out?

Try plugging a guitar cable in and out of the front panel Feedthru jack a few times. This jack has what are known as "normaling pins" that route the buffered signal to the rear panel Feedthru jack when nothing is plugged in to the front panel Feedthu jack... I'm guessing that A. you use the rear pan...
by JohnClark
Fri May 24, 2019 11:10 am
Forum: Racks, Switching Systems and MIDI
Topic: GCX buffer and reverse wah issue
Replies: 2
Views: 569

Re: GCX buffer and reverse wah issue

I suppose the first test would be to plug your Guitar directly into Loop 1 Input, that way you can tell if its just the GCX Buffer or if any of the six pedals also cause this problem with the backward wah. Also, I'd test if the backward wah is happy with the wireless by connecting the output of the ...
by JohnClark
Wed May 22, 2019 3:40 pm
Forum: Racks, Switching Systems and MIDI
Topic: Older ground control
Replies: 4
Views: 614

Re: Older ground control

Oh... why didn't you say so? ;) To get to the switch contacts you will need to remove the whole circuit board from the main chassis. First remove the bottom cover that is held on with the six small black screws (#1 Philips Head), then you will see the bottom of the circuit board. Remove the 6-8, dep...
by JohnClark
Wed May 22, 2019 2:43 pm
Forum: Racks, Switching Systems and MIDI
Topic: Older ground control
Replies: 4
Views: 614

Re: Older ground control

An Electronics Cleaner spray would be about the only thing that would work to get into the actual contacts on a tact switch. You would want a de-greaser type cleaner NOT one that lubricates... anything that lubricates will only end up attracting dirt and ultimately make matters worse. I hope that he...
by JohnClark
Tue May 14, 2019 9:59 am
Forum: Racks, Switching Systems and MIDI
Topic: i need help programming pllleeeeaaasee help
Replies: 2
Views: 601

Re: i need help programming pllleeeeaaasee help

It looks like you are most of the way there! Right on! 1. For the MIDI Routing, you will want to use the MIDI Thru jacks rather than the MIDI Out jacks on the Triaxis and G-Major. 2. You programmed the Ground Control Pro MIDI devices correctly it looks like, but you will need to go into each device ...
by JohnClark
Fri May 03, 2019 4:01 pm
Forum: Racks, Switching Systems and MIDI
Topic: Controlling PX-8 Plus with an RJM Mastermind LT
Replies: 2
Views: 581

Re: Controlling PX-8 Plus with an RJM Mastermind LT

Sorry to hear you are having troubles! In Loop Strip Mode you should see a blue light flash on the display whenever there is MIDI Data reaching the PX-8 Plus MIDI In. Do you see this light when sending data from the controller? PX-8 Plus will default to listening on MIDI Channel 1. When you say you ...